New Product

FRP Tank 14x65 – Resin, Sand and Carbon Tank with 2.5" Top Opening (1465)

₺19,945.76

VAT included · Free shipping in Türkiye

Installation is a service · plumbing is the customer’s responsibility

Free Shipping Across Türkiye
Fast Delivery Across Türkiye · 1–3 business days
2-Year Warranty Misuse is not covered.
Order by Phone 0850 304 95 25
SKU
WP-TK-006
Category
,

FRP · 14″ × 65″ · 2.5″ Threaded

A Corrosion-Free Body for Softening and Filtration with the FRP Tank 14×65

The FRP Tank 14×65 is a pressure tank with a glass-fibre reinforced composite body, 14 inches in diameter and 65 inches tall. A top-mounted valve is connected to the 2.5 inch threaded opening at the top; filled with resin, quartz sand or activated carbon, it is used as the body of water softening and filtration units.

Size
14" × 65"
Opening
2.5" Threaded · Top
Body
FRP Composite

01Problem & Solution

If the Body Is Not Sound, the System Stops

Problem

Heavy Bodies That Rust

In softening and filtration units the media works for years under pressure, constantly wet and, during regeneration, in contact with brine. In these conditions metal bodies can rust over time; and because they are heavy, they are also hard to move and position.

Solution

A Composite Body That Does Not Rust

The FRP Tank 14×65 is made by winding glass fibre over a plastic inner liner. The composite construction does not rust, withstands brine and is lighter than metal tanks of the same size; thanks to its 2.5 inch threaded opening it is used directly with top-mounted valves.

02Key Features

A Standard Size for Softening and Filtration

The FRP Tank 14×65 is a commonly used body size for softeners and for sand and carbon filters at building-inlet and commercial scale.

14″ × 65″ Size

Its nominal diameter is 14 inches (approximately 356 mm) and its nominal height is 65 inches (approximately 1,651 mm); in the trade it is also known as 1465.

2.5 Inch Threaded Top Opening

The single opening is at the top of the tank; top-mounted automatic and manual valves are fitted to this thread.

Glass-Fibre Reinforced Body

The layer of glass fibre wound over the inner liner gives the tank its pressure resistance.

Corrosion-Free Construction

The composite body does not rust; it is suitable for contact with the brine used in regeneration.

Works with Different Media

It works with media such as cationic resin, quartz sand, anthracite and activated carbon.

Black Tank Base

The tank stands upright on a black base that supports its rounded bottom dome.

03Technical Specifications

Tank Specifications

FeatureValue
Product TypeFRP Pressure Tank (Empty)
Tank Size14" × 65" (1465)
Nominal Diameter14" (≈356 mm)
Nominal Height65" (≈1,651 mm)
OpeningTop
Opening Connection2.5" Threaded
Body ConstructionGlass-Fibre Reinforced Composite
ColourBlue
BaseBlack Tank Base
Not IncludedValve · Distributor · Media

04Applications

Where Is It Used?

The FRP Tank 14×65 is used as the body of medium-scale softening and filtration units.

Water SoftenersSand FiltersActivated Carbon FiltersBuilding and Estate InletsWell Water TreatmentHotels and RestaurantsSmall Production PlantsReverse Osmosis Pre-Treatment

05How It Works

How Does the FRP Tank 14×65 Work?

The FRP Tank 14×65 does not treat water on its own; it is the pressurised body in which the media inside it and the valve fitted to it do their work. General information on the material that gives the body its strength can be found on the glass fibre page. Although the way it operates varies with the media, the sequence of flow is the same:

  1. The Distributor and Media Go In

    The riser tube and bottom distributor are placed in the tank first, followed by the resin, sand or activated carbon; freeboard is left at the top for the bed to expand.

  2. The Valve Is Fitted to the Top Opening

    The control valve is screwed into the 2.5 inch threaded opening; the inlet, outlet and drain lines are connected to the valve.

  3. The Water Passes Through the Media

    Raw water enters the tank through the valve and filters down through the media bed; hardness, sediment or chlorine is held back, depending on the type of media.

  4. Treated Water Leaves Through the Riser Tube

    The water collected at the distributor beneath the bed returns up the riser tube to the valve and from there to the plumbing.

  5. Backwash and Regeneration

    At the set interval the valve backwashes the media; in softening, the resin is regenerated with brine and the tank returns to service.

06Making the Right Choice

Is the FRP Tank 14×65 Right for Your System?

When choosing the FRP Tank 14×65, the valve connection, media volume, flow rate and installation site should be assessed together.

Valve Connection

The tank has a 2.5 inch threaded top opening; the valve to be used must suit a tank neck of this size. For example, the Runxin F73 Tandem Water Softener Valve is for tanks 8–14 inches in diameter.

Media Volume

The media volume is calculated from the water analysis and the capacity required. In our 20 Tonnes/Day Water Softening System, a tank of this size is used with 100 litres of resin.

Flow Rate

The tank diameter determines how fast water can pass through the bed; high-flow lines need a tank of larger diameter or tanks in parallel.

Installation Site

Clearance should be left above the tank, which is about 1.65 metres tall, for the valve and for maintenance; the floor must be level and load-bearing.

07Maintenance and Use

Notes That Protect Tank Life

Installed correctly and operated within the limits on its label, the FRP Tank 14×65 gives many years of service.

  • Stand the tank upright on a level, solid floor; when moving it, do not drag it by the threaded opening.
  • Do not force the thread when fitting the valve; the seal is made by the valve’s O-ring, and overtightening damages the thread.
  • Do not leave the tank where there is a risk of frost or in direct sunlight.
  • Use a vacuum breaker on installations where a vacuum can form in the line; a vacuum can damage the inner liner.
  • Do not exceed the maximum pressure and temperature stated on the label; use a pressure reducer on lines where the pressure fluctuates.

08Frequently Asked Questions

Common Questions

What does the FRP Tank 14×65 do?
It is the body that holds the media under pressure in water softeners and in sand and activated carbon filters. A valve is connected to the 2.5 inch threaded opening at the top; the water is treated as it passes through the media.
What does 14×65 mean?
The first number is the diameter of the tank in inches and the second its height: 14 inches in diameter (approximately 356 mm) and 65 inches tall (approximately 1,651 mm). The same size is also written as 1465.
Does the tank come with resin or a valve?
No. The FRP Tank 14×65 is sold as an empty tank; the valve, distributor, riser tube and media are chosen separately.
Which media is it used with?
It is used with softening and filtration media such as cationic resin, quartz sand, anthracite and activated carbon. The type and volume of media are determined by the water analysis.
Where should an FRP tank be installed?
It should be installed on a level, load-bearing floor, in a place that does not freeze and is out of direct sunlight. Enough clearance should be left above it for the valve and for maintenance.
Does the FRP tank come with a warranty?
Units, valves, pumps and tanks carry a 2-year warranty and taps a 1-year warranty. Filters, membranes, resin and salt are consumables and fall outside the warranty.

Reviews

There are no reviews yet.

Be the first to review “FRP Tank 14x65 – Resin, Sand and Carbon Tank with 2.5" Top Opening (1465)”

Questions & Answers

Questions asked about this product

Questions on compatibility, capacity and installation are answered by our technical team. The answers stay public — so the next person with the same question can see them too.

No questions have been published for this product yet. You can be the first to ask.

Ask a question about this product

Your email address will not be published. Questions are reviewed by our technical team and published together with the answer.

Delivery

Across Türkiye · 1–3 business days

Products in stock ship free anywhere in Türkiye and arrive within 1–3 business days. Items not in stock are supplied to order — the lead time is confirmed to you when the order is approved.

Installation

Installation is a service · plumbing is the customer’s responsibility

Fitting the part falls under our service work and is subject to a service fee. Plumbing labour and any pipes, valves and fittings are not included in the price; these items are the customer’s responsibility.

Warranty

2 years · manufacturer

This product is covered by a 2-year manufacturer warranty. During the warranty period, labour and parts are free for faults arising from manufacture. Consumables such as filters, membranes and resin are outside warranty cover — they are replaced when their service life ends; they do not fail.

Withdrawal and returns

Distance sales agreement

The right of withdrawal and the return terms are set out in detail in the distance sales agreement. Systems that have been installed and commissioned, and made-to-order products, are outside its scope.

Cancellation and return terms

How can we help?

Two different requests, two different forms.

The two forms ask different things: if we are building a new system we ask about your water and capacity; if your existing system needs service we ask for its brand and a photo.

Not sure? Call us and let’s work it out together: 0850 304 95 25

₺19,945.76 VAT included
Add to Cart